Quick Answer: How Do You Wire A Light With Two Black Wires?

Why does my outlet have 2 black and 2 white wires?

Since this one has more, it means it is part of a “series”.

A “series” means there are 2 or more outlets powered by the same wiring and circuit.

The other set of black and white wires goes to the next outlet down the line and that’s how it gets its power..

Is black wire positive?

Positive – The wire for the positive current is red. Negative – The wire for the negative current is black. Ground – The ground wire (if present) will be white or grey.

Which wire is positive when both are black?

If the multi-colored wire is black and red, the black wire is the negative wire, while the red one is positive. If both wires are black but one has a white stripe, the striped wire is negative, while the plain black wire is positive. Look in the owner manual to determine which wires are negative in a car.

What happens if you switch hot and neutral wires?

In North America, switching the hot and neutral wires on the AC breaker will cause a potential shock hazard with the polarized electrical outlets and lighting fixtures connected to that breaker. It’s not a good thing. You will have short circuited the breaker to the neutral, which will trip the breaker immediately.

What if both wires are black?

Black means hot, white signifies neutral, and green indicates ground. However, if you need to rewire a light switch or a plug socket, you may occasionally come across two black wires. It’s essential that you determine which black wire is hot before proceeding.

Does it matter which wire goes where on a light switch?

If your switch has a “LINE” marking, the always hot wire goes to this. The other connection will be “LOAD” where the load (ie light fixture) is wired. The load wire may have red electrical tape on it to differentiate.

What happens if you wire a light fixture backwards?

The fixture still works if you reverse the wires, but the socket sleeve will be hot, and anyone who touches it while changing a bulb can get a shock. When wired correctly, the socket sleeve is neutral and only the small metal tab at the base of the socket is hot.

Why does my light switch have 3 black wires?

If the light turns on, the second black wire you connected to the switch is the switch feed and the unconnected black wire is the feed to the other loads. If the light doesn’t turn on, then it’s the other way around: the connected wire feeds the other loads and the disconnected wire is the light feed.

Is it OK to install a light fixture without a ground wire?

If the fixture is out of reach, the lack of a ground is probably a low risk. If it is a pull chain light, use of a string pull rather than metal is a good idea. Yes, if you have a metal light fixture your fixture needs to be grounded. The ground wire exits your junction box, but it is not attached to your junction box.

Is it OK to not ground a light switch?

If you are replacing a switch a ground is not required, as per the above exception. However, if you’re installing a switch; replacement or otherwise, into a metal box that is grounded. The switch will be ground via the devices yoke and mounting screws. So if the metal box is grounded, the switch is also grounded.

What happens if you connect a positive wire to a negative wire?

If you connect positive to negative directly with a wire, you get a very low resistance circuit. The lower the resistance, the higher the current. The is called a short circuit. … Batteries have internal resistance, so this has to be added to the resistance of the wire.

Why does light switch have 2 black wires?

The bare or green-wrapped ground wires serve as a backup to divert the power safely away in case of an electrical fault. In most cases, two black wires will be attached to the switch’s two terminal screws.

What if my light switch has no ground wire?

Going without a ground wire If the light switch has a screw for a bare ground wire but your electrical box doesn’t have one, you’re OK just leaving that screw empty and connecting your other wires to the hot screws. … If the box isn’t grounded, the switch will still work.

Why are both white and black wires hot?

like the title says both wires (black and white get or turn hot). To answer your question, Yes, that is correct. The reason you are getting 120 volts when the fan/light is on is because the voltage is feeding trough the motor or the light bulb (or both).

What color is positive wire?

redUS recommended DC power circuit wiring color codesFunctionlabelColorPositive (of a positive grounded) circuitNwhiteNegative (of a positive grounded) circuitL-black3-wire grounded DC Power SystemPositiveL+red9 more rows

How do you wire a light switch with two black wires?

Connect the top screw to the wire that feeds to the light. Connect the bottom screw to the hot wire. When you turn the power back on, and if you want to swap the direction of the switch (as in press down to turn off, or turn on), turn off the power and switch the two black wires.