# Question: Where Do The Red Black And White Wires Go On A Light Switch?

## Which wire is live red or black?

Black (neutral) Red (live) Green and yellow (earth).

## Do I need to connect the red wire?

Typically, all the white wires in junction box will be connected together. The black wire is the “hot” (or power-source) wire. … The red wire would the “load” wire (controlled by the switch.) It would be connected to the black wire of the “load” (light fixture, outlet controlled by switch, fan, etc.)

## Why do I have 3 red wires in my light switch?

The third red wire goes into one of the two terminals along with one of the other reds. The third red is the feed to the next lights in the circuit, in your case the bathroom. It will have been in one of the terminals on the old switch along with the live feed (one of the reds) from the last light in the circuit.

## Where does the black and white wire go on a light switch?

When you turn on a light switch, power goes to the light through the “hot” (black) wire and then back through the neutral (white) wire to the ground. The bare or green-wrapped ground wires serve as a backup to divert the power safely away in case of an electrical fault.

## What happens if you reverse hot and neutral wires?

If your outlet’s polarity is reversed, it means that the neutral wire is connected to where the hot wire is supposed to be. This may not sound like a terrible thing, but it is. There is always electricity flowing out of an outlet with reversed polarity, even if an appliance is supposed to be off.

## Can you connect black and white wires together?

A single black and white connected together is normal. It is part of a switch loop. A black connected to a group of whites is not normal and probably should be connected to the other blacks. It is normal to have a white connected to a group of blacks if a switch loop is used.

## Does it matter which wire goes where on a light switch?

If it’s a single pole switch with two terminals, the answer is no. One wire is the power to the switch and the other wire goes to the light. … The black wire (hot) is switched so both black wires are connected to the switch. The switch may have gold and silver colored screws.

## Does red wire go to white?

In North American house 240 vac wiring the White is ALWAYS neutral, the Black is Always hot and Red is the other hot wire. Black to White: 120 v. Red to White: 120 v.

## What are the red white and black wires on a light switch?

Basic Knowledge of How to Wire a Light SwitchBlack Wire – This is the hot or load wire.White Wire – This is the neutral wire.Bare Copper (Green) Wire – This is your ground wire.Red Wire – This wire is used for 3 or 4 way switches and will connect the switches together so they can each control your lights.

## Can black and red wires go together?

If the red and black wires are connected together already and energized, yes you can do that but you will need a pull chain light or a remote control, if they are not switch controlled.

## What happens if you wire a light switch backwards?

Normal switches only have two poles and cannot be wired backwards. The black wire is the hot wire and a black wires go on each pole. … If you put a white wire and a black wire on the switch poles the best case is that you get a dead short and you trip the breaker. The worst case is the switch explodes and creates a fire.

## Which color wires go together?

US, AC:The US National Electrical Code only mandates white (or grey) for the neutral power conductor and bare copper, green, or green with yellow stripe for the protective ground. In principle any other colors except these may be used for the power conductors.

## Is red wire the same as white?

The white wire is always neutral, and when the cable has only two conductors, as most 120-volt cables do, the hot wire is black. The ground wire is usually left bare, but in some cases, the ground wire color is green. In a three-conductor cable, the extra wire is red, and it’s almost always used as a hot wire.

## Why does my light switch have 2 red wires?

Usually, a twin red cable implies a switch wire, consisting of a permanent live, and a switch return wire.

## How do you wire a light switch with a black and white red wire?

First, twist the two bare copper ground wires together. Twist the two red wires together and attach a wire nut. Take the white wire from switch two and twist it with the black wire from switch one. Mark the white wire with a piece of electrical tape to indicate that the wire is now a hot wire.

## Does red wire go with white or black?

Connect the green wire to your household ground wire (copper/bare wire). Connect your white wires together and secure with wire nut. Connect the red wire in the ceiling to the black wire in the light kit and the black wire in the ceiling to the black wire in the fan.

## Which wire is hot if both are black?

However, if both wires are hot, the reading will be zero. The United States has strict codes relating to home wiring, including clearly defined colors on the outer casing of the wires. Black means hot, white signifies neutral, and green indicates ground.

## Is red or black positive?

The positive (red) cable should be attached to the positive terminals on each battery. The negative (black) cable should have one end attached to the negative terminal of the dead battery, and one end grounded.

## What do you do with the red wire when installing a light?

Hence, my question, what do I do with the RED wire? The answer is that the Red Wire is the Hot Wire from the switch itself. You are wiring your fixture into a junction box where buku wires come together. Hook the white to white, ground to ground and RED to the BLACK Light Fixture Wires.

## What are black and red wires?

Remember, black and red wires are always hot, meaning they are source wires that carry power from the electric service panel to a destination, such as an outlet or a light.

## What does a red wire mean in a light switch?

What are Red Wires? Red wires are usually used as secondary hot wires. Red wires are also hot and should be clearly marked to avoid the dangers of electrocution. Red wires are commonly used when installing ceiling fans, where the light switch maybe.