# Light Fixture Has Two Black Wires No White

## What happens if I wire light switch wrong?

If a light switch is wired up wrongly, a short circuit may takes place if you give phase and neutral to the switch terminals.

Always connect neutral wire to the one terminal of the light and phase to the one terminal of the switch and off wire to the other terminal of the switch to the light other terminal..

## What happens if you switch line and load wires?

Here’s what happens when somebody wires a GFCI receptacle with the load and line wires reversed: The GFCI will work, in the sense that you can plug in a hair dryer and the hair dryer will blow hot air. If the load and line wiring gets messed up, a ground fault (radio in the tub) won’t trip the GFCI.

## What happens if you switch black and white wires?

In that case if you just touch the bare wires together you get a short circuit. It will produce a big spark and hopefully blow a fuse or trip a breaker. If you wire them together and then turn the power on, the spark will occur at the breaker or fuse.

## Which wire is positive when both are black?

If the multi-colored wire is black and red, the black wire is the negative wire, while the red one is positive. If both wires are black but one has a white stripe, the striped wire is negative, while the plain black wire is positive.

## Why does my outlet have 2 black and 2 white wires?

The two black conductors are electrically bonded through the receptacle, as are the two white conductors. You’ll notice that the bonding tab on the side of the receptacle is still in place, which means that the two receptacles are connected together.

## What happens if you wire a light fixture backwards?

The fixture still works if you reverse the wires, but the socket sleeve will be hot, and anyone who touches it while changing a bulb can get a shock. When wired correctly, the socket sleeve is neutral and only the small metal tab at the base of the socket is hot.

## How many wires can you run off one outlet?

1 Answer. The receptacle manufacturer should document how many wires can be put where. In general, if there are screws, you can use at most one wire per screw. For quickwire/backwire holes, you can only use one wire per hole, and further, that one wire can only be 14 gauge.

## How do you wire a light with two black wires?

Connect the top screw to the wire that feeds to the light. Connect the bottom screw to the hot wire. When you turn the power back on, and if you want to swap the direction of the switch (as in press down to turn off, or turn on), turn off the power and switch the two black wires.

## Why does my light switch have two black wires?

The bare or green-wrapped ground wires serve as a backup to divert the power safely away in case of an electrical fault. In most cases, two black wires will be attached to the switch’s two terminal screws.

## Why does my light switch have 3 black wires?

One of the black wires is probably the feed from the breaker box. One is probably a feed to the receptacles. The third one would go to the light. The receptacle wire should be connected to the feed wire along with one terminal of the switch.

## What happens if you touch two live wires together?

You will receive an electrical shock. You will receive a shock if you touch two wires at different voltages at the same time. You will receive a shock if you touch a live wire and are grounded at the same time. When a circuit, electrical component, or equipment is energized, a potential shock hazard is present.

## What if both wires are black?

You will get a reading if one wire is hot and the other isn’t. However, if both wires are hot, the reading will be zero. … However, if you need to rewire a light switch or a plug socket, you may occasionally come across two black wires. It’s essential that you determine which black wire is hot before proceeding.

## Can Reverse polarity cause a fire?

Watch out: Reversed polarity on an electrical outlet is dangerous. If you accidentally reverse these wires the device you plug in to the receptacle may “work” but it is unsafe and risks a short circuit, shock, or fire.

## Can 2 hot wires share a neutral?

It is NOT permitted to share a neutral in any other situation. If you were to share a neutral with two breakers on the same leg of a panel, both circuits could draw the breaker limit (lets say 15A) making the shared neutral as much as 30A return current!

## Why would a neutral wire be hot?

If the neutral is disconnected anywhere between the light bulb and the panel, then the neutral from the light to the point of the break in the neutral will become hot (and the device will be unpowered, because no current will be flowing through it). … It might be best to temporarily unscrew any such bulbs.

## What happens if you reverse hot and neutral wires?

If your outlet’s polarity is reversed, it means that the neutral wire is connected to where the hot wire is supposed to be. This may not sound like a terrible thing, but it is. There is always electricity flowing out of an outlet with reversed polarity, even if an appliance is supposed to be off.

## Why would an outlet have 2 hot wires?

The reason for multiple hot/neutral wires for one outlet is that the outlets are daisy-chained together. This means hot/neutral is only coming from one of the wires and it is being sent to the other wire.

## Can you connect black and white wires together?

A single black and white connected together is normal. It is part of a switch loop. A black connected to a group of whites is not normal and probably should be connected to the other blacks. It is normal to have a white connected to a group of blacks if a switch loop is used.